Hook Reference › O. Mustad & Son Hooks › Mustad 9260 E — Beak Hooks

O. Mustad & Son 9260 E

Beak Hooks

Marks: P photographically · V verified · I inferred · E estimated · S speculative What they mean

Photographic record

2 photographs

Side view of a silver-colored fishhook on grid paper, showing a deep rounded bend, a barb near the point, two slices on the shank, and a small ring eye turned down.
IMG-2Mustad — New entry — image 2 Loose hook paired with the box, side view. Two raised slices on the shank, a single barb near the point, a bright finish, and a closed ring eye turned down.

Identify

Mustad 9260 E is recorded here from one boxed size 4 specimen. Its lid label names the line “Mustad – Beak Hooks” and gives O. Mustad & Sön of Oslo as the maker P.

The label states the point type, offset, and eye construction. The photographs show the shank slices, the barb, and the shape of the bend, but not the offset or the point grinding P.

How to identify it

The lid label opens with “Qual. 9260 E,” with “Hollow Point” beneath it. The product name, “Mustad – Beak Hooks,” is printed in red across the center P.

A three-line block follows: “Forged Reversed,” “T. d. tapered eye Nickelplated,” and “With 2 slices in shank.” The maker line reads “O. MUSTAD & SÖN,” above “OSLO — NORWAY.” On the recorded box, the “No.” at lower left carries only a faint pencil mark resembling a 4 P.

The trademark at upper right is a black line drawing of a bird-of-prey head in profile, with a fishhook that appears to curve out from beneath the beak P.

Measurements & specifications

Features of the model, as recorded
FeatureRecordedEvidence
EyeBall Eye, Turned Down
Show noteHide note

Closed ring eye, turned down toward the point side P. The label states 'T. d. tapered eye'; the oblique side view cannot confirm taper.

OBS-1LBL-5
WireExtra-Fine, Forged
ShankShort (1X–2X Short) — Baitholder slices
BendBeak / Reversed Point, Wide gap, Offset / kirbed
PointBeak / Reversed
Show noteHide note

Single cut barb on the inside face near the point, angled back toward the bend and set a short distance behind the point tip P.

OBS-4
FinishNickelled — stated on packaging
Show noteHide note

The label prints 'Nickelplated'. The surface is bright and silver-colored, with no bronzed, blued or japanned coating visible P.

LBL-5OBS-6

The wire is flat-faced, with a streaked, textured surface along the outer curve P. Two raised slices are cut from the upper edge of the shank, both angled toward the eye P. The eye is a closed ring turned down toward the point side P.

The label states a reversed point, meaning the point is offset to the right when viewed from the eye looking down the shank. It also states a hollow point. The flat side view cannot show offset or hollow grinding, so neither is confirmed on the hook.

The shank is short in proportion to the total length I. Caliper values recorded for size 4 are total length ~18.8 mm, shank ~12.3 mm, gap ~9.2 mm, and wire ~0.8 mm E. No caliper reading appears in the photographs.

Measurements

Overall length18.8 mm EcaliperMEA-1
Shank length12.3 mm EcaliperMEA-2
Gap width9.2 mm EcaliperMEA-3
Wire diameter0.8 mm EcaliperMEA-4

Size 4, specimen S1. Bend depth, weight and the shank-to-gap ratio are in the full table.

All recorded values
Per size, with how each dimension was taken
SizeOverall lengthShank lengthGap widthBend depthWire diameterWeight
4Specimen S118.8 mm EcaliperMEA-112.3 mm EcaliperMEA-29.2 mm EcaliperMEA-3—0.8 mm EcaliperMEA-4—
Calibrated SVG True-scale preview

How the measurements are defined
How hook dimensions are measuredA hook outline with dimension lines for overall length, shank length, gap, bend depth, and wire diameter.Overall lengthShank lengthGapBend depthWire diameter
Overall length
Eye to the farthest point of the bend.
Shank length
Eye to the start of the bend.
Gap
Point to shank, at right angles to the shank.
Bend depth
Shank to the bottom of the bend.
Wire diameter
Across the wire, measured by caliper where possible.

Use & alternatives

  • Bait fishing

Label & packaging

This record documents one specimen. It describes that specimen only, not every example of the model.

S1 · Boxed size 4, loose hook

Size
4 (from the existing record)
Container
Box
Hook condition
Clean, bright surface with no visible rust or pitting. A few dust specks lie on the outer bend. Point and barb appear intact.
Packaging condition
Fair — significant wear, partially legible
Measured
size 4
Photographs
IMG-1IMG-2
Detailed condition observations
Wear
lid label, upper left and centre: brown or yellow staining across the label paper LBL-11
Wear
lid label, across the red line and the specification block: light seam lines and creases across the label, consistent with tape edges or folds LBL-12
Wear
lid, lower edge and corners: frayed and torn paper along the lower lid edge with a loose strip; corners scuffed LBL-13

The loose hook is paired with the box on the strength of its file name and the label description. Nothing in the photographs links them directly, and the box contents are not shown. Label staining, creases, and a frayed, torn lower lid edge with scuffed corners are recorded.

Full label transcription
LBL-1 printed · lid label, top left from IMG-1
Qual. 9260 E
LBL-2 printed · lid label, upper left, under model line from IMG-1
Hollow Point
LBL-3 trademark · lid label, upper right from IMG-1
LBL-4 printed · lid label, centre, red print from IMG-1
Mustad - Beak Hooks
LBL-5 printed · lid label, centre, three-line specification block from IMG-1
Forged  Reversed
T. d. tapered eye  Nickelplated
With 2 slices in shank
LBL-6 printed · lid label, lower centre from IMG-1
O. MUSTAD & SÖN
OSLO — NORWAY
LBL-7 printed · lid label, lower left from IMG-1
No.
LBL-8 handwritten · lid label, right side, over end of 'Nickelplated' from IMG-1
QTY[?]
22
LBL-9 handwritten · lid label, lower right beside SÖN and NORWAY from IMG-1
heavy circular ink scribble; anything beneath is unreadable [?]
LBL-10 pencil · lid label, above 'No.', left of maker line (faint) from IMG-1
4
Trademark
Black line-and-hatch drawing at the upper right of the label: a bird-of-prey head in profile facing left, with a fishhook that appears to curve out from beneath the beak, its bend sweeping right and down and its point curling back up and to the left.
As entered on the specimen record
Qual. 9260 E
Hollow Point
Mustad - Beak Hooks
Forged  Reversed
T. d. tapered eye  Nickelplated
With 2 slices in shank
O. MUSTAD & SÖN
OSLO — NORWAY
No.
Layout
Model code and 'Hollow Point' at upper left, trademark drawing at upper right, product name in red print at center, three-line specification block below it, maker name and place at lower center, 'No.' at lower left.
Later marks
Pen, right side of label over the end of 'Nickelplated': QTY[?] on one line, 22 below it.
Pen, lower right beside 'SÖN' and 'NORWAY': heavy circular ink scribble; anything beneath is unreadable [?].
Pencil, above 'No.': faint mark resembling a 4.

Condition

The photographed hook has a clean, bright surface with no visible rust or pitting. A few dust specks lie on the outer bend. Point and barb appear intact P.

History & dating

Sources & research

Sources & documentation

This specimen and its packaging — photographed, 2 images
Supports: ConstructionCountry of originEyeBarbFinishCondition notes
+10 morefewerMeasurement notesMeasurements availableOverall lengthShank lengthGap widthWire diameter measuredPackagingSummaryIdentificationTechnical notes

Entry updated October 28, 2026.