O. Mustad & Son 3601

Mustad-Treble Hooks

Marks: P photographically · V verified · I inferred · E estimated · S speculative What they mean

Photographic record

3 photographs

Mustad 3601 Treble Hooks — top-down view showing three barbs, hollow-point geometry, and tapered eye junction — size No. 2 — bronzed
IMG-2Mustad 3601 Treble Size 2 Top View Hollow Points Side-profile view of the Mustad 3601 Treble Hook, size No. 2, on a 0.1-inch grid, showing fine transverse ridges across the blind tapered shank end, brass brazing, and hollow-ground points (P).

Identify

The Mustad 3601 is a treble hook pattern produced by O. Mustad & Son in Oslo, Norway, labeled on the examined box as Mustad-Treble Hooks in Tapered Bronzed finish with Hollow Point geometry P. The photographed size No. 2 specimen (S1) joins three round-wire Sproat bends with yellow brass brazing along the upper shank into a blind tapered end marked with fine transverse ridges P.

Each of the three points features a concave inner hollow-ground taper and a single cut barb beneath a warm brown bronzed coating P. The paired cardboard box lid carries the brown-ink Key Brand skeleton key label for a 1/4 gross lot, hand-annotated in blue ink with TREBLE above the label and 2 after the printed No. P.

How to identify it

Look for the brown-ink Key Brand skeleton key trademark on the left side of the lid label alongside O. MUSTAD & SON, OSLO - NORWAY, Qual. 3601, and Mustad-Treble Hooks P. On this box (V1), 1/4 Gr. Tapered Bronzed and No. are printed, while the size numeral 2 is handwritten in blue ink and TREBLE is written across the upper lid P.

On the hook itself, check the upper shank junction for exposed yellow-gold brass brazing where the three round wires meet, and examine the blind tapered tip for fine transverse ridges rather than a ball eye or flat spade P. Confirm that all three Sproat bends are un-offset and carry concave hollow-ground points P.

Inferred Identification · Model

Loose Mustad 3601 hooks can be separated from ball-eye trebles by the blind ridged taper and from japanned or tinned blind trebles by the bronzed finish and hollow-ground Sproat points.

How we got there

Basis: Label LBL-2 specifies Qual. 3601, Hollow Point, and Tapered Bronzed, matching the observed ridged blind taper (OBS-1, OBS-2), Sproat bends (OBS-3), hollow points (OBS-4), and bronzed finish (OBS-6).

Reasoning: Checking the eye termination, shank grooving, point inner profile, and coating together narrows unboxed Mustad trebles to the 3601 specification.

Measurements & specifications

Features of the model, as recorded
FeatureRecordedEvidence
EyeBlind — Marked Tapered Shank
Show noteHide note

Three shanks converge into a blind tapered end with no loop, ball, or spade; fine transverse ridges mark the tapered upper section P.

OBS-1OBS-2IMG-2
WireStandard, Round
ShankStandard — Tapered, Marked / ridgedOBS-1OBS-2IMG-2
BendSproat, Standard gap
Show noteHide note

Three symmetrical rounded Sproat bends are spaced equally around the central axis without offset P.

OBS-3
PointHollow Point
Show noteHide note

Each of the three points carries a single sharp, well-defined cut barb on its inner face P.

OBS-5
FinishBronzed — stated on packaging
Show noteHide note

Label specifies Tapered Bronzed P; steel wire carries a uniform warm brown bronzed finish interrupted by exposed yellow-gold brazing alloy at the upper shank join P.

LBL-2OBS-2OBS-6
ConstructionTreble

Blind Marked Tapered Shank: Rather than terminating in a welded ball eye, the three round-wire shanks converge and taper smoothly to a narrow rounded tip without flattening P. Fine transverse ridges cut across the tapered upper section provide mechanical grip for whipping or snelling line directly to the taper, while yellow brass brazing secures the three shanks together P.

Hollow-Ground Points: Each of the three points exhibits a concave inner taper between the cut barb and the needle tip, matching the Hollow Point specification printed on the lid label P.

Symmetrical Sproat Treble Geometry: Three rounded Sproat-style bends radiate equally around the central shank axis with no lateral offset, giving each point an independent bite angle P.

Measurements

Overall length27.8 mm PcaliperMEA-1
Shank length18.6 mm PcaliperMEA-2
Gap width9.3 mm PcaliperMEA-3
Wire diameter0.89 mm PcaliperMEA-4

Size 2, specimen S1. Bend depth, weight and the shank-to-gap ratio are in the full table.

All recorded values
Per size, with how each dimension was taken
SizeOverall lengthShank lengthGap widthBend depthWire diameterWeightShank:gap
2Specimen S127.8 mm PcaliperMEA-118.6 mm PcaliperMEA-29.3 mm PcaliperMEA-313 mm Pcaliper0.89 mm PcaliperMEA-4.572g Pmethod not recorded~2.0:1
How the measurements are defined
How hook dimensions are measuredA hook outline with dimension lines for overall length, shank length, gap, bend depth, and wire diameter.Overall lengthShank lengthGapBend depthWire diameter
Overall length
Eye to the farthest point of the bend.
Shank length
Eye to the start of the bend.
Gap
Point to shank, at right angles to the shank.
Bend depth
Shank to the bottom of the bend.
Wire diameter
Across the wire, measured by caliper where possible.

Treble Size Specification and Scale

Treble hook sizing assigns the size number to each individual hook in the three-hook assembly rather than scaling the combined width to a single hook of the same nominal number. On this size No. 2 specimen (S1), each of the three Sproat-bend hooks has a 0.035″ (0.89 mm) wire diameter and 0.367″ (9.32 mm) gap width, while the complete assembly measures 1.095″ (27.81 mm) in total length from the blind tapered tip to the crown of the bends P.

Own this hook? Help us measure it.

We have measurement for size 2. Know any others? Submit calipered measurements and we'll review and add them. Thank you!

Inferred Design · Model

The Mustad 3601 pairs a brass-brazed, ridged blind tapered shank with hollow-ground Sproat bends to provide a secure, non-slip tie-in surface without the bulk of a looped or ball eye.

How we got there

Basis: Observations OBS-1, OBS-2, OBS-3, and OBS-4 document three round-wire Sproat-bend hooks brazed together with yellow brass alloy, tapered to a smooth blind tip, and scored with fine transverse ridges along the upper taper.

Reasoning: In pre-ball-eye treble construction, whipping gut, wire, or heavy line directly onto a tapered shank risked slippage under tension; transverse grooves cut across the taper bite into the wrapping material while the gradual taper avoids an abrupt metal edge.

Use & alternatives

  • Bait fishing
  • Saltwater

Primary application

The Mustad 3601 is built as a multi-point treble hook for bait rigging and lure hardware in freshwater and saltwater fishing P. Its three equally spaced Sproat bends and concave hollow points provide three independent hooking angles, while the ridged blind tapered shank accommodates direct line whipping or snell attachment P.

Inferred Application · Model

These trebles are suited to whipped or snelled bait rigs, trolling harnesses, and vintage wooden plug hardware where a snell or wire loop is bound directly to the tapered shank.

How we got there

Basis: Specimen S1 has a blind marked tapered shank with no eye opening (OBS-1, OBS-2), three symmetrical Sproat bends (OBS-3), and concave hollow points (OBS-4) in 0.89 mm bronzed wire (MEA-4, OBS-6).

Reasoning: Because a blind tapered shank cannot accept a split ring directly, rigging requires whipping a gut, braided, or wire loop onto the ridged taper, a standard method for classic bait rigs, spinner traces, and snelled plug hooks.

Modern equivalents

Modern equivalents
HookMatchNotes
Mustad 3551Very goodModern Mustad treble, Sproat bend, ball eye, available in comparable sizes
Gamakatsu F314GoodContemporary treble hook for saltwater and bait applications

Inferred Comparison · Specimen S1

Although labeled size No. 2, this treble has a shorter 1.095-inch total length and narrower 0.367-inch individual gap than a single No. 2 bait or streamer hook.

How we got there

Basis: Label LBL-4 marks the specimen as size 2, while caliper measurements MEA-1, MEA-2, and MEA-3 record 27.81 mm (1.095 in) total length, 18.64 mm (0.734 in) shank length, and 9.32 mm (0.367 in) gap width.

Reasoning: Treble hook sizing scales each component bend individually while keeping the shared shank compact so the three points balance cleanly on lures and baits without excessive leverage.

Label & packaging

Specimens, packaging, and label

This record documents one specimen. It describes that specimen only, not every example of the model.

S1 · Box and hook, size No. 2

Size
2 (printed on the label)
Container
Box
Hook condition
Clean, intact bronzed finish with no active rust or pitting; all three hollow points and barbs are sharp and unbent (P).
Packaging condition
Good — moderate wear, legible
Measured
size 2
Photographs
IMG-1IMG-2IMG-3
Detailed condition observations
Wear
box lid exterior: Heavy surface staining, adhesive or water residue around label perimeter, scuffing, and corner and edge wear on off-white cardboard lid. LBL-5
Wear
lid label surface and edges: Age toning, dark edge residue, small scuff over the H in Hooks, and minor corner and border wear. LBL-6

Paired hook and box specimen (S1); hook features three round-wire Sproat bends joined with yellow brass brazing into a blind tapered shank end marked with fine transverse ridges P.

Full label transcription
LBL-1 trademark · lid label, left column from IMG-3
Key
[key emblem]
Brand
LBL-2 printed · lid label, center and lower area inside asterisk border from IMG-3
O. MUSTAD & SON
Manufacturers
OSLO - NORWAY
Qual. 3601
Hollow Point
Mustad-Treble Hooks
1/4 Gr. Tapered Bronzed
No. Made In Norway
LBL-3 handwritten · box lid, upper left above label from IMG-3
TREBLE
LBL-4 handwritten · lid label, lower left after printed No. from IMG-3
2
Trademark
Vertical skeleton key emblem printed in brown ink between Key above and Brand below on the left side of the label P.
As entered on the specimen record
Key
[key emblem]
Brand

O. MUSTAD & SON
Manufacturers
OSLO - NORWAY
Qual. 3601
Hollow Point
Mustad-Treble Hooks
1/4 Gr. Tapered Bronzed
No. Made In Norway
Layout
Brown-ink rectangular paper label glued to the off-white cardboard lid and framed by a border of printed asterisks; vertical skeleton key emblem sits in the left column between Key and Brand P.
Typeface
Brown serif and sans-serif printed lettering with italic Mustad-Treble Hooks line P.
Printed marks
Decorative asterisk border; Key Brand skeleton key trademark; O. MUSTAD & SON / Manufacturers / OSLO - NORWAY / Qual. 3601 / Hollow Point / Mustad-Treble Hooks / 1/4 Gr. Tapered Bronzed / No. Made In Norway P.
Later marks
TREBLE handwritten in blue ink on the box lid above the label; numeral 2 handwritten in blue ink after printed No. at lower left of the label P.

Care of this specimen: Store in a cool, dry place below 50% relative humidity away from direct sunlight and dissimilar metals; keep the cardboard lid and paper label dry and untreated.

Condition

Hook is clean and free of rust or pitting with sharp, unbent points P. Cardboard box lid shows heavy staining and edge wear; paper label is intact and legible P.

Storage and Preservation

Store the bronzed hook and cardboard box in a cool, dry environment below 50% relative humidity and out of direct sunlight to slow finish oxidation and paper deterioration P. Keep the hook separated from dissimilar metals to avoid galvanic corrosion, and handle the points carefully to protect the hollow-ground tips P.

Leave the stained cardboard lid and glued paper label dry and untreated; avoid moisture, solvents, or abrasive cleaning that could lift the brown printing or blue ink annotations P.

Inferred Packaging · Packaging

Box V1 uses a standard quarter-gross (36-hook) pre-printed Mustad treble label that relied on hand-written size numbering at packing time.

How we got there

Basis: Label LBL-2 prints 1/4 Gr. and No. with a blank space where the numeral 2 is added in blue ink (LBL-4), accompanied by TREBLE written in matching blue ink on the box lid (LBL-3).

Reasoning: Printing generic model and finish labels without fixed size numerals allowed Mustad packers to label small quarter-gross boxes across multiple sizes from a single label stock.

Label and source analysis

Hand-Annotated Labeling

Two blue-ink handwritten markings appear on the box lid (V1): TREBLE is written in block capitals across the upper left cardboard above the label, and the numeral 2 is written in the lower left margin of the label directly after the printed abbreviation No. P.

Because the label prints No. without a size figure, the handwritten 2 supplies the size designation for this 1/4 Gr. box, while the TREBLE inscription on the lid identifies the hook type on the outer cardboard P.

History & dating

Series

O. Mustad & Son of Oslo, Norway cataloged the 3601 under its Mustad-Treble Hooks designation as a tapered, bronzed, hollow-point treble pattern P. The examined box lid (V1) identifies the maker as O. MUSTAD & SON, Manufacturers, OSLO - NORWAY with the Key Brand skeleton key mark and a 1/4 Gr. (36-hook) packaging unit P.

This record does not include dated Mustad trade catalogs establishing the exact introduction or discontinuation years of quality code 3601.

Dating

Lid label prints O. MUSTAD & SON, Manufacturers, OSLO - NORWAY without a postal code, alongside the Key Brand skeleton key trademark and no barcode P.

Inferred Period · Packaging

Packaging

We read box V1 as mid-twentieth-century Norwegian export packaging from O. Mustad & Son's Oslo era prior to the introduction of postal codes and retail barcodes.

How we got there

Basis: Lid label LBL-1 and LBL-2 print O. MUSTAD & SON, Manufacturers, OSLO - NORWAY without a postal code, use the brown-ink Key Brand skeleton key trademark, omit any barcode, and leave the size numeral blank for hand-inked completion (LBL-4).

Reasoning: Norwegian postal codes were introduced in 1968 and retail barcodes followed in the 1970s, while hand-stamped or hand-written size numerals on pre-printed 1/4 gross box labels reflect mid-century batch labeling practices.

Value & buying

4.5 / 10CollectabilityRarity: Uncommon

Vintage Mustad 3601 treble hooks retain period packaging interest when paired with an intact Oslo-era Key Brand label, though this record does not establish scarcity or demand.

Specimen Appeal: Original Oslo-era Mustad boxes retaining legible Key Brand labels, period hand-inked size annotations, and clean bronzed hooks with intact brass-brazed tapered shanks offer clear documentary and technical interest for tackle historians P.

Market Evidence Limits: This record does not establish scarcity, collector demand, or completed auction prices for the Mustad 3601. Condition factors visible on the examined specimen include heavy staining and edge wear on the cardboard box lid, minor scuffing on the intact paper label, and clean, rust-free bronzed steel on the hook P.

No recorded sold sales in this record. Value depends on box lid legibility, completeness of the 1/4 gross count, and absence of rust on the bronzed hooks P.

Where to find

Vintage tackle auctions, online collectibles marketplaces, and estate tackle lots.

Inferred Collector interest · Model

Collector interest in the Mustad 3601 centers on vintage lure restoration, classic snelled treble rigging, and Oslo-era Key Brand packaging examples.

How we got there

Basis: The specimen preserves an Oslo Key Brand lid label with hand-inked annotations (LBL-1, LBL-2, LBL-3, LBL-4) paired with a clean brass-brazed blind-tapered treble (OBS-1, OBS-2, OBS-7).

Reasoning: Restorers of early wooden plugs and period bait rigs seek authentic blind-tapered trebles for whipping onto wire or gut traces, while packaging collectors value complete Oslo-imprinted Mustad boxes.

Sources & research

Sources & documentation

This specimen and its packaging — photographed, 3 images
Supports: Quantity per packageEyeBendShankFinishBarb
+23 morefewerCondition notesMeasurement notesOverall lengthShank lengthGap widthWire diameter measuredWeightDating rangePackagingCollectability summaryMarket value lowMarket value highMarket value basisMarket sold observationsMarket value notesWhere to findFun factSummaryIdentificationTechnical notesSeries historyPrimary applicationCollectability detail

Open questions

  1. Which Mustad trade catalogs list quality code 3601, and what size range and production dates do they document?No period Mustad catalog page or price list is attached to verify the manufactured size range or production dates.Can you help? Share scans or citations from dated O. Mustad & Son catalogs showing model 3601.

Entry updated November 21, 2026.